Facebook Pixel Code
x
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.

Engineering and Construction Lab Report Samples

Industrial process control
The second experiment concerned the proportional control where the ability of the controller to maintain optimal levels with variations in measurements was observed. Te third experiment involved the introduction of an external stressor to the system and then observing the response of ths sytem to...
Pages: 7 (1750 words) , Lab Report , Social Control , Media Control
Preview Essay
Steel Report
Lastly, secimen RW11. 9was cold robbed riled wire which was also made from middle steel material. Te surface was relatively smoother and malleable but the specimen was easier to bend than specimenR12. I terms of the geometry of the specimens, 12 had a diameter of...
Pages: 5 (1250 words) , Lab Report
Preview Essay
Impact of a water Jet laboratory
This was part one of the experiment in which one had to determine the Freezing Temperature of Pure Lauric Acid. Ater this part, te next procedure was to add about 300 mL of tap water with a temperature of 20–25°C to a 400 mL beaker...
Pages: 6 (1500 words) , Lab Report , Down Syndrome , Chemistry
Preview Essay
Jominy Hardenability test
Hardness using the Rockwell scale along the cooled bar length, ad comparing the curves of experimental hardenability with the curves of the published hardenability. Hrdenability entails the extent to which, asubstance or material is hardened following a complete process of heat treatment. A widely...
Pages: 7 (1750 words) , Lab Report , Test
Preview Essay
Lab#2 concrete mix design and compression tests
The aggregates used must be well graded to minimize air voids in the concrete matrix. Gnerally, cncrete mix designs are currently being over-designed for the fear of production of results that will not meet the minimum strength criteria specified by the engineer concerned. Tere is...
Pages: 10 (2500 words) , Lab Report , Standardized Tests
Preview Essay
Construction development in China
There are a lot of tourist centers in urban districts and suburbs of Shanghai, wich form many tourist areas, turist lines and special-interest tourist items. (hanghai National Information, 2013). Troughout the past century, Sanghai has had numerous name tags attached to it; lke "Paris of...
Pages: 15 (3750 words) , Lab Report , Plate Tectonics , China
Preview Essay
Measuring Forces in Truss Members Using Strain Gages
It is important to determine the magnitude of force on every structural member and the direction of the force, wich aids in designing various structural members so that they can withstand forces in them. Tis determination is also important in coming up with and selecting...
Pages: 10 (2500 words) , Lab Report , Strain Theory
Preview Essay
Determination of principle stress
In this regard, te maximum normal stress was found to be 52. 5MPa, mnimum normal stress was found to be -18. 5MPa, pinciple angle 34. 2degrees, Mximum shear stress was 35. 5MPa, Mximum shear angle 10. 8degrees, ad angle was 79. Te Obtained results...
Pages: 5 (1250 words) , Lab Report , Wage Determination , Work Stress
Preview Essay
Design and analysis (aerodynamics) of the new nose (2nd design) for open wheel climb race car in by using CFD (computational fluid dynamics). [1750 words]
At the higher nose of the nosecone, uder tray CL increase but front wings CL decrease. Tis operation of the machine makes it possible for any change in ride height, te body of full car CL will change. A the same time, wen the front...
Pages: 7 (1750 words) , Lab Report , Aerodynamics
Preview Essay
Electric circuits and devices prototyping
Since a BJT is three terminal device, i can be connected in three possible ways with one terminal being common for both input and output. Tese three configurations include common base, cmmon collector and common emitter configurations. Te common base configuration has high voltage gain...
Pages: 7 (1750 words) , Lab Report , General Electric , Electric Cars
Preview Essay
Taping over uneven ground
The plumb bobs present in the image are those of field engineering where they have to be sharp to the point and this is critical to ensure that the centre of gravity remains high on the bob to eliminate false results. Te above image is...
Preview Essay
Taping over uneven ground
The plumb bobs present in the image are those of field engineering where they have to be sharp to the point and this is critical to ensure that the centre of gravity remains high on the bob to eliminate false results. Te above image is...
Preview Essay
Physics lab report
A positive different in (x-x0) indicates that the force is negative x direction. Anegative (x-x0) implies a positive force direction. Gven a displacement initially A = x-x0, F= -kA, ad accelerates towards the negative x-axis towards equilibrium; x= x0 where the restoring force is zero....
Pages: 5 (1250 words) , Lab Report , Position , Physics
Preview Essay
Electrical circuits
Results of the values of component rating have been documented and analyzed. Te discussion and analysis section gives view about the results. RC response characteristics in different connection conditions have been put out expounding on the effects of loading and use of active and passive...
Pages: 15 (3750 words) , Lab Report , Electrical Engineering
Preview Essay
Refrigeration Laboratory
The inefficient motor should also be replaced with an efficient one so as to save energy. Fiction reduction measures are very important. Lbricant and oil should be smeared on the Inner lining of the walls of the suction pipes to reduce friction between the fluids...
Pages: 8 (2000 words) , Lab Report , Ozone Layer , Duke Ellington
Preview Essay
Designing and implementing a precision rectifier circuits
Of rectification is the diode. Tis type of rectification helps in converting the whole incoming /input waveform to output having a constant polarity which may be a negative or a positive. i the process it converts two polarities of incoming. wveform to pulsating...
Pages: 5 (1250 words) , Lab Report
Preview Essay
Measurement and instruments
The features include low current consumption, 35V to 24V DC operation voltage, oen-Collector pre-driver, wde operating voltage range, tmperature compensation, 50mA maximum sinking output current and reverse polarity protection. Tis is the Hall Effect named after Edwin Hall who discovered this in 1879. The principle...
Preview Essay
Learning from Disaster
The change was effected, ad the contract’s Shop Drawing 30 and Erection E-3 were also changed. Afew days later, 42 new shop drawings were sent to G. ,which included the revised drawings. Tn days later, te pictures were returned to Havens, cmplete with the stamp...
Pages: 8 (2000 words) , Lab Report , Natural Disaster , Disaster
Preview Essay
Cooling Tower
The cooling process is carried via reduction or taking away of hot liquid from the plant’s condenser, ad then directing or transferring the heat from the hot liquid to the atmosphere; mstly water is utilized as the thermal heat sink. Te load tank has two...
Pages: 11 (2750 words) , Lab Report , Eiffel Tower
Preview Essay
Solar cell
Therefore, te contact grid should be made such that it allows more photons o penetrate and the same time it should collect more electrons. O hitting the Silicon surface, te energy of the photon transfer to the valence electron in the n-type. Te energy makes...
Pages: 4 (1000 words) , Lab Report , Solar Power , Solar Energy in English
Preview Essay

Related Engineering and Construction Lab Report Essay Examples

1 - 20 results of 104 items
WE CAN HELP TO FIND AN ESSAYDidn't find an essay?

Please type your essay title, choose your document type, enter your email and we send you essay samples

Contact Us